OLE Client Specification

From RISC OS

(Difference between revisions)
Jump to: navigation, search
m (The client: two-way, with dash)
m (Quitting the client: typo)
 
(14 intermediate revisions not shown)
Line 21: Line 21:
The client should check to see if an OLEServer$Type_XXX variable
The client should check to see if an OLEServer$Type_XXX variable
exists for its file type.
exists for its file type.
-
(If it cannot find such a variable, then the client may wish to
+
If it cannot find such a variable then there is no server known for
-
use the OLESupport module which simulates the response of a server
+
that file type at the moment.
-
for particular file types.
+
The client may then choose to
-
See [http://www.xs4all.nl/~erikgrnh/riscos/OLESuppDoc.txt OLESuppDoc]
+
use the OLESupport module. It can simulate the response of a server
-
for information on how to
+
for a chosen file type.
-
use this module task).
+
If the client does not want to use the OLESupport module, then the OLE attempt
 +
has failed at this point. The client should inform the user and clean
 +
up any internal data.
-
===Start the session===
+
Note that if the OLESupport module has been used earlier for a particular
-
Having found a server variable, the client should save its data to
+
file type, then there will already be an environment variable, which points
-
disc and send an OpenSession message with format 0 as a broadcast,
+
to the module. If that is so, the client will find this variable in the first
-
using the unique name specified in the variable. If the server is
+
step, and transparently use the module, using the normal message protocol.
-
already running it will respond with an acknowledge.
+
-
If there is no acknowledgement, the client will get its message back
+
It is advisable to check for this variable every time an OLE session is requested,
-
as a User_Message_Acknowledge (19) message. It should then try to
+
and not, e.g. only once when the client application starts or when the first OLE
-
start the server using the -R token and again broadcast the OpenSession
+
session is started. During the runtime of the client the variable may well change,
-
message, this time with format 1. If again the message is not
+
for example because a server was seen by the Filer.
-
acknowledged, the session failed. The client should delete the data
+
-
file it created and tidy up.
+
-
In the case that all is well, the server will have acknowledged the
+
===Using the OLESupport module===
-
OpenSession message and will also respond by sending a
+
: ''See [http://www.xs4all.nl/~erikgrnh/riscos/OLESuppDoc.txt OLESuppDoc] for the original document.
-
Message_OLEOpenSessionAck to inform the client a session is truely
+
First the client must check if the module is loaded, by calling the OLE_Version SWI
-
open.
+
in the X variant:
 +
  SWI XOLE_Version (&67B00)
 +
  On entry -
 +
  On exit  - R0 = Major revision number
 +
            R1 = Minor revision number
 +
            R2 = Task handle (0 if task not running)
 +
  Errors  - Overflow set if SWI is not known
 +
On normal exit (overflow clear) the module is already loaded. The server should proceed by calling the OLE_SimulateSession SWI as described below.
 +
 
 +
If an error is returned the module is not yet loaded. The client should then try to start it with:
 +
  SWI XWimp_StartTask (&600DE)
 +
  On entry - R0 = ^ "<Path$Dir>.OLESupport"
 +
  On exit  - R0 = Task handle of module task (0 if task quit)
 +
  Errors  - Overflow set if command failed
 +
:''Note: the command string in R0 was taken from OLESuppDoc. It should be replaced with the correct string to start a module task. Should probably be "System:Modules.OLESupport".''
 +
If an error is returned, the module could not be found and the OLE session will have failed.
 +
 
 +
Now that the module is running, the client can ask it to handle sessions for the
 +
desired file type by calling OLE_SimulateSession:
 +
  SWI OLE_SimulateSession (&47B05)
 +
  On entry - R0 = file type
 +
  On exit  -
 +
The module will create an environment variable of the form
 +
  OLEServer$Type_XXX : -N OLESupport -R /Desktop_OLESupport
 +
and will be ready to receive and send all OLE messages relevant to this file type.
 +
In effect the client can communicate transparently with the module as if it were
 +
a real OLE server.
 +
 
 +
The next step for the client is to start from the top: read the environment variable, send a broadcast, etc. Care must be taken not to fall into an endless loop if the environment variable the client looks for is not found. It should only attempt to start the module at most once for each OLE session.
 +
 
 +
===Start the session===
 +
Having found a server variable, the client should save its data to
 +
disc in a suitable temporary location (see [[Programming Conventions#Scrap usage]])
 +
and send an OpenSession message with format 0 as a User_Message_Recorded (18) broadcast
 +
using the unique name specified in the variable.  
     Message_OLEOpenSession (&80E21)
     Message_OLEOpenSession (&80E21)
Line 76: Line 109:
               R1+8 = my_ref (unique Wimp-generated word > 0)
               R1+8 = my_ref (unique Wimp-generated word > 0)
 +
If the server is
 +
already running it will respond with an acknowledge.
-
A format 0 message should be sent initially. If a task is running
+
If there is no acknowledgement, the client will get its message back
-
which recognises the message it will reply correctly. If the client
+
as a User_Message_Acknowledge (19) message. It should then try to
-
receives the same message back (format 0) because no-one acknowledged
+
start the server using the -R token and again broadcast a recorded OpenSession
-
it, it should attempt to start the server task using the value of the
+
message, this time with format 1. If again the message is not
-
-R parameter specified in the
+
acknowledged, the session failed. The client should inform the user,
-
OLEServer$ variable. It should then set the format to 1 and send
+
delete the data file it created and tidy up.
-
the message to the server task using the task handle returned by
+
 
-
Wimp_StartTask.
+
In the case that all is well, the server will have acknowledged the
-
If it receives a format 1 message back
+
OpenSession message by sending an
-
unacknowledged it knows the server has died in some way and it should
+
OLEOpenSessionAck message to inform the client a session is truely
-
remove the data file.
+
open.
 +
:''Note: the following information on format 2 messages is dubious. See the [[Talk:OLE Client Specification#Format 2|talk page]]''
If a client knows it already has a link to a server, it should not
If a client knows it already has a link to a server, it should not
attempt to send a format 0 open session message. It can send a format
attempt to send a format 0 open session message. It can send a format
Line 109: Line 145:
     message number field (+16).
     message number field (+16).
This message tells the client that a session was
This message tells the client that a session was
-
opened successfully and may expect Message_OLEFileChanged messages. The sending
+
opened successfully and may expect OLEFileChanged messages. The sending
of this message by the server has several effects:
of this message by the server has several effects:
*Because it sets the your_ref field to the my_ref field of the OLEOpenSession message, it tells the WIMP that it has acknowledged that message and the client will not get that OLEOpenSession message bounced back to it.
*Because it sets the your_ref field to the my_ref field of the OLEOpenSession message, it tells the WIMP that it has acknowledged that message and the client will not get that OLEOpenSession message bounced back to it.
Line 138: Line 174:
Note that the server should not feel it owns the file and thus should not
Note that the server should not feel it owns the file and thus should not
-
attempt to delete the file during emergencies. Also, if the server corrupts
+
attempt to delete the file during emergencies. However, when the OLESupport module is
 +
used the editing program invoked by the module will have no such limitations and might
 +
delete the file.
 +
 
 +
If the server corrupts
the file, the client should be capable of working out that the file
the file, the client should be capable of working out that the file
format has been compromised when it receives an OLEFileChanged and reads back the file.
format has been compromised when it receives an OLEFileChanged and reads back the file.
Line 146: Line 186:
a format 0 message, providing the new pathname at +28.
a format 0 message, providing the new pathname at +28.
-
The client can now read the changed file from disk, though it is not obliged
+
The client should now read the changed file from disk.
-
to do so. It can also remember the data for this session has changed and
+
-
only read it back when the session is closed.
+
===Closing the session===
===Closing the session===
Line 172: Line 210:
session from its list.
session from its list.
-
Note that the client can send this message to a server or broadcast it to
+
Note that not only can a server send this message to a client,
 +
the client can send this message to a server or broadcast it to
all servers when sessions are being closed from the client's end. (i.e.
all servers when sessions are being closed from the client's end. (i.e.
the user is closing the application down or removing one of its
the user is closing the application down or removing one of its
Line 185: Line 224:
When a client is closing down, it should broadcast this message with
When a client is closing down, it should broadcast this message with
the Session number set to -1. The servers that are handling its OLE
the Session number set to -1. The servers that are handling its OLE
-
editing sessions then know that these sessions can be abandoned.
+
editing sessions then know that sessions for this client can be abandoned.
Similarly, when a server closes down, it will also send a broadcast
Similarly, when a server closes down, it will also send a broadcast
Line 191: Line 230:
sessions open with this server (recognised by the server task handle)
sessions open with this server (recognised by the server task handle)
should drop those sessions.
should drop those sessions.
-
 
==Actions a client should take==
==Actions a client should take==
Line 198: Line 236:
When a client wants to start an OLE session, it
When a client wants to start an OLE session, it
should write the file to disk and check for the environment variable
should write the file to disk and check for the environment variable
-
for the proper file type. It
+
for the proper file type.
 +
If no environment variable (and thus no server) is found, it could try to use the OLESupport
 +
module, which can be made to create an appropriate variable and operate as a server.
 +
The client
should make sure it can handle the messages as described in
should make sure it can handle the messages as described in
[[#Messages to be handled by the client]], i.e. have the appropriate
[[#Messages to be handled by the client]], i.e. have the appropriate
message handlers installed. It should
message handlers installed. It should
generate a Session number and remember it belongs to this particular session
generate a Session number and remember it belongs to this particular session
-
in its internal data. It should then broadcast an OLEOpenSession
+
in its internal data. It should then broadcast an OLEOpenSession format 0
User_Message_Recorded (type 18) message.
User_Message_Recorded (type 18) message.
 +
The handler for the OLEOpenSession message will deal with any problems in
The handler for the OLEOpenSession message will deal with any problems in
case the server was not running. The other handlers will deal with the
case the server was not running. The other handlers will deal with the
Line 216: Line 258:
===Quitting the client===
===Quitting the client===
-
If the client it closing down and it still has sessions open, it should
+
If the client is closing down and it still has sessions open, it should
either send each of the servers it knows about an OLECLoseSession User
either send each of the servers it knows about an OLECLoseSession User
message with the Session number set to -1 ( = close all sessions),  
message with the Session number set to -1 ( = close all sessions),  
Line 223: Line 265:
Actually, the client could simply broadcast the message, regardless of
Actually, the client could simply broadcast the message, regardless of
whether it has, or ever had, any sessions open.
whether it has, or ever had, any sessions open.
-
 
==Messages to be handled by the client==
==Messages to be handled by the client==
Line 249: Line 290:
The client receives one of these messages as a type 19 message
The client receives one of these messages as a type 19 message
-
(User_Message_Acknownledge) when the broadcast of the message by the
+
(User_Message_Acknowledge) when the broadcast of the message by the
client itself was not acknowledged. It should take further action to
client itself was not acknowledged. It should take further action to
try to get the server to respond.
try to get the server to respond.
-
 
-
The client should check the task handle of the sender to see if it
 
-
is its own task handle. (The client's task handle can be found in
 
-
the block pointed to by R1 after it sent the OLEOpenSession message
 
-
with Wimp_SendMessage).
 
Note that this message may also arrive due to a broadcast by another
Note that this message may also arrive due to a broadcast by another
-
client who is looking for a server. In that case the task handle of the
+
client who is looking for a server, or even receive its own message
-
sender will be different from the client's own task handle, and
+
back as part of the broadcast. In that case
it will be a type 17
it will be a type 17
(User_Message) or, more likely, type 18 (User_Message_Recorded) message.
(User_Message) or, more likely, type 18 (User_Message_Recorded) message.
Line 268: Line 304:
If a format 0 message comes back, this means the server is not running.
If a format 0 message comes back, this means the server is not running.
The client should try to start the server using the value in the -R field
The client should try to start the server using the value in the -R field
-
of the environment variable. If the Wimp_StartTask of the server failed
+
of the environment variable to Wimp_StartTask. If that fails
-
(it returned a task handle of 0)
+
(it returned an error or a task handle of 0)
-
the client should consider the attempt failed and display an appropriate
+
the client should consider the attempted OLE session failed, display an appropriate
-
message to the user, and clean up (remove the saved file, remove the session
+
message to the user, and clean up (remove the temporary file, remove the session
from its internal list, etc).
from its internal list, etc).
-
On succes, the client should send a new OLEOpenSession User_Message_Recorded (18)
+
If the server was started successfully, the client should send a new OLEOpenSession User_Message_Recorded (18)
message directly
message directly
to the server, using the task handle returned by Wimp_StartTask,
to the server, using the task handle returned by Wimp_StartTask,
this time with format set to 1.
this time with format set to 1.
 +
:''Note: experiments have shown that existing clients often broadcast this message. See [[Talk:OLE Client Specification#Broadcast or direct]]''
====Format 1====
====Format 1====
Line 284: Line 321:
refuses to handle the file for some reason). The client should assume the
refuses to handle the file for some reason). The client should assume the
session failed, inform the user with a suitable message,
session failed, inform the user with a suitable message,
-
and clean up (remove the saved file, remove the session
+
and clean up (remove the temporary file, remove the session
from its internal list, etc).
from its internal list, etc).
Line 293: Line 330:
send an OLEOpenSession message with
send an OLEOpenSession message with
format 0 and continue the same way as for the original session.
format 0 and continue the same way as for the original session.
-
 
===OLEOpenSessionAck===
===OLEOpenSessionAck===
Line 362: Line 398:
If there is a session, it can read the modified file (from the
If there is a session, it can read the modified file (from the
original path for format 1, the given path for format 0). The client
original path for format 1, the given path for format 0). The client
-
presumably may want to display the modified file in its own window.
+
may want to display the modified file in its own window.
-
 
+
-
On the other hand, a client may choose to delay the update of its data
+
-
until the session is closed.
+
Note that this message does not imply that the session is over. The
Note that this message does not imply that the session is over. The
Line 428: Line 461:
;-R <RunCommand>
;-R <RunCommand>
-
:This token allows a potential client to '''run''' the server. It should provide a string which can be passed directly to Wimp_StartTask. This should start with a run command an be followed by the location of the server. This location could be an expanded pathname or more usually a system variable. Note that the RunCommand can contain spaces, and for convenience '''-R''' should be the last token in the variable. Examples:  
+
:This token allows a potential client to '''run''' the server. It should provide a string which can be passed directly to Wimp_StartTask. This should start with a run command and be followed by the location of the server. This location could be an expanded pathname or more usually a system variable. Note that the RunCommand can contain spaces, and for convenience '''-R''' should be the last token in the variable. Examples:  
  run <Draw$Dir>
  run <Draw$Dir>
  /<Draw$Dir>
  /<Draw$Dir>
-
 
==Session numbers & task handles==
==Session numbers & task handles==
Line 440: Line 472:
unique for the run time of the program. The client should also keep a copy
unique for the run time of the program. The client should also keep a copy
of the server's task handle which it will receive via
of the server's task handle which it will receive via
-
Message_OLEOpenSessionAck. This way it can inform the server whenever it
+
the OLEOpenSessionAck message. This way it can inform the server whenever it
-
closes down.
+
closes down and recognise messages sent by the server.
 +
 
 +
Note that the combination of client task handle and session number uniquely
 +
identifies a session.
 +
 
 +
A session number is limited to 24 bits (it is unknown why this is), so using
 +
pointers to internal data structures as session numbers is not practical.
 +
A recommended strategy for generating session numbers by a client is to simply
 +
start at 1 when the application starts and increment by one for each new session.
 +
Assuming the user starts a new OLE session every 5 seconds for 12 hours a day,
 +
seven days a week it will take more than five years for the counter to run out.
 +
 
 +
==See Also==
 +
*[[OLE]]
 +
*[[OLE Specification]]
 +
*[[OLE Server Specification]]
 +
*[[User Messages]]
 +
 
 +
[[Category:Protocols]]

Latest revision as of 16:32, 16 January 2014

There are still many points unclear about this protocol. You can discuss them on the Talk page.

This page is intended as a full description of the Computer Concepts OLE protocol as seen from the client side. A programmer writing an application should be able to find here all the information required to let the application work as an OLE client. To let the application work as an OLE server, see the OLE Server Specification.

Contents

The client

A client application (such as a desktop publishing program, or a mail handler) may wish to edit data it is capable of loading and rendering (such as drawfiles or plain text files). Such an application could provide facilities to edit these files itself, or use an already resident editor by sharing the file with it.

It seems sensible and easier to choose the second option, in which case the client needs to ask a 'compliant' server to engage in a two-way data sharing session.

An OLE session

An OLE session should be initiated by a client application.

Checking the environment variable

The client should check to see if an OLEServer$Type_XXX variable exists for its file type. If it cannot find such a variable then there is no server known for that file type at the moment. The client may then choose to use the OLESupport module. It can simulate the response of a server for a chosen file type. If the client does not want to use the OLESupport module, then the OLE attempt has failed at this point. The client should inform the user and clean up any internal data.

Note that if the OLESupport module has been used earlier for a particular file type, then there will already be an environment variable, which points to the module. If that is so, the client will find this variable in the first step, and transparently use the module, using the normal message protocol.

It is advisable to check for this variable every time an OLE session is requested, and not, e.g. only once when the client application starts or when the first OLE session is started. During the runtime of the client the variable may well change, for example because a server was seen by the Filer.

Using the OLESupport module

See OLESuppDoc for the original document.

First the client must check if the module is loaded, by calling the OLE_Version SWI in the X variant:

 SWI XOLE_Version (&67B00)
 On entry -
 On exit  - R0 = Major revision number
            R1 = Minor revision number
            R2 = Task handle (0 if task not running)
 Errors   - Overflow set if SWI is not known

On normal exit (overflow clear) the module is already loaded. The server should proceed by calling the OLE_SimulateSession SWI as described below.

If an error is returned the module is not yet loaded. The client should then try to start it with:

 SWI XWimp_StartTask (&600DE)
 On entry - R0 = ^ "<Path$Dir>.OLESupport"
 On exit  - R0 = Task handle of module task (0 if task quit)
 Errors   - Overflow set if command failed
Note: the command string in R0 was taken from OLESuppDoc. It should be replaced with the correct string to start a module task. Should probably be "System:Modules.OLESupport".

If an error is returned, the module could not be found and the OLE session will have failed.

Now that the module is running, the client can ask it to handle sessions for the desired file type by calling OLE_SimulateSession:

 SWI OLE_SimulateSession (&47B05)
 On entry - R0 = file type
 On exit  -

The module will create an environment variable of the form

 OLEServer$Type_XXX : -N OLESupport -R /Desktop_OLESupport

and will be ready to receive and send all OLE messages relevant to this file type. In effect the client can communicate transparently with the module as if it were a real OLE server.

The next step for the client is to start from the top: read the environment variable, send a broadcast, etc. Care must be taken not to fall into an endless loop if the environment variable the client looks for is not found. It should only attempt to start the module at most once for each OLE session.

Start the session

Having found a server variable, the client should save its data to disc in a suitable temporary location (see Programming Conventions#Scrap usage) and send an OpenSession message with format 0 as a User_Message_Recorded (18) broadcast using the unique name specified in the variable.

   Message_OLEOpenSession (&80E21)
   -------------------------------

   SWI Wimp_SendMessage (&400E7)
   On entry - R0 = User message recorded (18)
            - R1 = ^Block
                +0 = length of block
                +4 = not used on entry
                +8 = not used on entry
               +12 = your_ref (=0, this is an original message)
               +16 = message number (&80E21)
               +20 = the 16 byte unique name from the -N tag, padded with zero bytes
               +36 = window handle of display holding file
               +40 = x offset of data in window
               +44 = y offset of data in window
               +48 = format number
                format = 0 or 1 (edit file)
                 +52 = Session number (24 bit number invented by the client)
                 +56 = file type
                 +60 = full pathname of the data file, zero terminated
                format = 2 (re-edit file)
                 +52 = Session number (24 bit number invented by the client)
                format > 2 (reserved for future expansion)
            - R2 = 0 (broadcast)

   On exit  - R0 = corrupted
            Message block is updated:
              R1+4 = task handle of sender (i.e. us, the client)
              R1+8 = my_ref (unique Wimp-generated word > 0)

If the server is already running it will respond with an acknowledge.

If there is no acknowledgement, the client will get its message back as a User_Message_Acknowledge (19) message. It should then try to start the server using the -R token and again broadcast a recorded OpenSession message, this time with format 1. If again the message is not acknowledged, the session failed. The client should inform the user, delete the data file it created and tidy up.

In the case that all is well, the server will have acknowledged the OpenSession message by sending an OLEOpenSessionAck message to inform the client a session is truely open.

Note: the following information on format 2 messages is dubious. See the talk page

If a client knows it already has a link to a server, it should not attempt to send a format 0 open session message. It can send a format 2 message which will inform a server that the user has tried to perform an OLE action on the same data a second time. This gives those applications which allow documents to be closed, but not lost from memory (eg ArtWorks) a chance to reopen an edit window on the data.

If a format 2 message comes back unacknowledged, the server has presumably died in the meantime. The client should start from scratch with a format 0 message.

The server replies

   Message_OLEOpenSessionAck (&80E22)
   ----------------------------------

   The server returns the same block as OpenSession but copies my_ref (+8)
   to your_ref (+12) and puts the OLEOpenSessionAck code (&80E22) in the
   message number field (+16).

This message tells the client that a session was opened successfully and may expect OLEFileChanged messages. The sending of this message by the server has several effects:

  • Because it sets the your_ref field to the my_ref field of the OLEOpenSession message, it tells the WIMP that it has acknowledged that message and the client will not get that OLEOpenSession message bounced back to it.
  • A new message (OLEOpenSessionAck) is sent to the client and can be used by the client to mark the session as open.
  • It tells the client what the task handle of the server is. Though the client might have gotten a task handle from the Wimp_StartTask call it used to start the server, in the most common cases the server will already be running, so this is the first point at which the client is informed of the task handle of the server.

The data has changed

Whenever the server saves data back to file, it sends an OLEFileChanged User message to the client (using the task handle passed in OLEOpenSession). This message format is as follows

   Message_OLEFileChanged (&80E1E)
   -------------------------------
                +0 = length of block
                +4 = task handle of sender
                +8 = my ref
               +12 = 0
               +16 = message number (&80E1E)
               +20 = format number
                 format = 0 (saved to a different file) then
                  +24 = Session number
                  +28 = full pathname of data, zero terminated
                 format = 1 (saved to the same file) then
                  +24 = Session number
                        (format used by OLESupport)
                 format > 1 then
                  +24... reserved for future extensions

Note that the server should not feel it owns the file and thus should not attempt to delete the file during emergencies. However, when the OLESupport module is used the editing program invoked by the module will have no such limitations and might delete the file.

If the server corrupts the file, the client should be capable of working out that the file format has been compromised when it receives an OLEFileChanged and reads back the file.

The server will send a format 1 message when it saved the data to the same file. If the data was saved to a different file, it will send a format 0 message, providing the new pathname at +28.

The client should now read the changed file from disk.

Closing the session

Whenever the server throws data away through user action (in particular when the editing window is closed), it sends a User message back to the client informing it that the session has been terminated.

   Message_OLECloseSession (&80E23)
   --------------------------------
                +0 = length of block
                +4 = task handle of sender
                +8 = my ref
               +12 = 0
               +16 = message number (&80E23)
               +20 = format number
                 format = 0 then
                   +24 = Session number (-1 means all sessions are closing)
                 format > 0 reserved for future extensions

This message tells the client that the session has ended and the file was not modified any further. It should remove the file and drop this session from its list.

Note that not only can a server send this message to a client, the client can send this message to a server or broadcast it to all servers when sessions are being closed from the client's end. (i.e. the user is closing the application down or removing one of its documents).

When a document is removed from the client (e.g. a Draw picture is deleted from a DTP application document) and there was an OLE session for that document, the client should send this message to the server with the appropriate Session number filled in. The server can then abandon the edit of this document.

When a client is closing down, it should broadcast this message with the Session number set to -1. The servers that are handling its OLE editing sessions then know that sessions for this client can be abandoned.

Similarly, when a server closes down, it will also send a broadcast of this message with the Session number set to -1. Clients who have sessions open with this server (recognised by the server task handle) should drop those sessions.

Actions a client should take

Starting a session

When a client wants to start an OLE session, it should write the file to disk and check for the environment variable for the proper file type. If no environment variable (and thus no server) is found, it could try to use the OLESupport module, which can be made to create an appropriate variable and operate as a server. The client should make sure it can handle the messages as described in #Messages to be handled by the client, i.e. have the appropriate message handlers installed. It should generate a Session number and remember it belongs to this particular session in its internal data. It should then broadcast an OLEOpenSession format 0 User_Message_Recorded (type 18) message.

The handler for the OLEOpenSession message will deal with any problems in case the server was not running. The other handlers will deal with the rest of the session.

Discarding a file

When the user takes an action in the client application that discards an object for which an OLE session is in progress, the client should send an OLECloseSession User message to the server. It should then clean up (remove the file, etc).

Quitting the client

If the client is closing down and it still has sessions open, it should either send each of the servers it knows about an OLECLoseSession User message with the Session number set to -1 ( = close all sessions), or broadcast such a message.

Actually, the client could simply broadcast the message, regardless of whether it has, or ever had, any sessions open.

Messages to be handled by the client

OLEOpenSession

Message_OLEOpenSession (&80E21)
-------------------------------
     +0 = length of block
     +4 = task handle of the sender (a client)
     +8 = my_ref
    +12 = 0
    +16 = message number (&80E21)
    +20 = 16 byte unique name padded with zeros
    +36 = window handle of display holding file
    +40 = x offset of data in window
    +44 = y offset of data in window
    +48 = format number
     format = 0 or 1 (edit file)
      +52 = Session number
      +56 = file type
      +60 = full pathname of data, zero terminated
     format = 2 (re-edit file)
      +52 = Session number
     format > 2 (reserved for future expansion) 

The client receives one of these messages as a type 19 message (User_Message_Acknowledge) when the broadcast of the message by the client itself was not acknowledged. It should take further action to try to get the server to respond.

Note that this message may also arrive due to a broadcast by another client who is looking for a server, or even receive its own message back as part of the broadcast. In that case it will be a type 17 (User_Message) or, more likely, type 18 (User_Message_Recorded) message. These should be ignored by the client.

Format 0

If a format 0 message comes back, this means the server is not running. The client should try to start the server using the value in the -R field of the environment variable to Wimp_StartTask. If that fails (it returned an error or a task handle of 0) the client should consider the attempted OLE session failed, display an appropriate message to the user, and clean up (remove the temporary file, remove the session from its internal list, etc).

If the server was started successfully, the client should send a new OLEOpenSession User_Message_Recorded (18) message directly to the server, using the task handle returned by Wimp_StartTask, this time with format set to 1.

Note: experiments have shown that existing clients often broadcast this message. See Talk:OLE Client Specification#Broadcast or direct

Format 1

If a format 1 message comes back, this means that we tried to start the server but it either died or does not acknowledge the message (i.e. it refuses to handle the file for some reason). The client should assume the session failed, inform the user with a suitable message, and clean up (remove the temporary file, remove the session from its internal list, etc).

Format 2

If a format 2 message comes back, the server apparently has died since the last contact. The client should clean up the old session and start a new OLE session from scratch, i.e. read the environment variable, send an OLEOpenSession message with format 0 and continue the same way as for the original session.

OLEOpenSessionAck

Message_OLEOpenSessionAck (&80E22)
----------------------------------
     +0 = length of block
     +4 = task handle of the sender (the server)
     +8 = my_ref
    +12 = your_ref (copy of my_ref from the OLEOpenSession sent by the client)
    +16 = message number (&80E22)
    +20 = 16 byte unique name padded with zeros
    +36 = window handle of display holding file
    +40 = x offset of data in window
    +44 = y offset of data in window
    +48 = format number
     format = 0 or 1 (edit file)
      +52 = Session number
      +56 = file type
      +60 = full pathname of data, zero terminated
    format = 2 (re-edit file)
      +52 = Session number
    format > 2 (reserved for future expansion)

This message means we are in business. The server is working on the document and the client may expect OLEFileChanged messages for it.

It is a copy of the OLEOpenSession message the client sent to the server, with the your_ref field filled with the value of the my_ref of the client's original message, and the message code replaced with the code for OLEOpenSessionAck (&80E22).

The client should check the your_ref value to see if it matches the my_ref of an OLEOpenSession message it sent, and check the Session number. If there is no match, the message should be ignored.

If the message is recognised the client should make a note of the task handle of the sender for this Session number. It will need this task handle to recognise messages coming from this server and when sending a message to the server.


OLEFileChanged

Message_OLEFileChanged (&80E1E)
-------------------------------
     +0 = length of block
     +4 = task handle of sender (the server)
     +8 = my ref
    +12 = 0
    +16 = message number (&80E1E)
    +20 = format number
      format = 0 (saved to a different file) then
       +24 = Session number
       +28 = full pathname of data, zero terminated
      format = 1 (saved to the same file) then
       +24 = Session number
             (format used by OLESupport)
      format > 1 then
       +24... reserved for future extensions

This is what OLE is all about. The client is informed that the file has been changed by the server.

The client must check if it knows the task handle of the server as given in the message, and has a session with the given Session number open with it. If not, it should ignore the message.

If there is a session, it can read the modified file (from the original path for format 1, the given path for format 0). The client may want to display the modified file in its own window.

Note that this message does not imply that the session is over. The server may issue more OLEFileChanged messages for this file.

OLECloseSession

Message_OLECloseSession (&80E23)
--------------------------------
     +0 = length of block
     +4 = task handle of sender (a server or client)
     +8 = my ref
    +12 = 0
    +16 = message number (&80E23)
    +20 = format number
      format = 0 then
        +24 = Session number (-1 means all sessions are closing)
      format > 0 reserved for future extensions

This message is sent by a server when it wants to close a session (probably because the user has finished editing the object) or when it is shutting down, in which case all its sessions should be closed (Session number = -1).

The client must check if it knows the task handle of the sender as a server it has open sessions associated with. If not, it should ignore the message.

For the given session number the client should remove the file on disk (if it still exists), and remove the session from its list of active sessions. If the session number was -1, it should do so for all open sessions which were handled by the server identified by the given task handle.

The server variable

Any application which provides its own file type and is capable of editing such files may set itself up to be an OLE server. To do so it needs to create a system variable, outlining the file type it can edit.

The syntax of this variable is as follows:

Variable name  = OLEServer$Type_XXX
Variable value = -N <UniqueName> -R <RunCommand>

X          = 0..9 | A..F
AlphaChar  = 0..9 | A..Z | a..z
UniqueName = [1..16]*<AlphaChar> (i.e. one to sixteen AlphaChars)
RunCommand = A * command string that will start the server

Spaces must be used as separators. The -N token should always be first and the -R token last. Both tokens must be present.

Typical examples are

  OLEServer$Type_AFF : -N OLESupport -R /Desktop_OLESupport
  OLEServer$Type_FFF : -N StrongED -R /ADFS::HardDisk4.$.Apps.!StrongED


Tokens

-N <UniqueName>
This token specifies a unique name to identify the server in an OpenSession message. This message is broadcast so it is up to the server who recognises the name to respond. This string can be up to 16 characters long. When passed in messages it should be specified as a 16 byte string with all unused bytes zeroed.
Note the server name should be modelled on the application name such as 'OLESupport' used by the support module or 'StrongED' as used by the StrongED text editor.
-R <RunCommand>
This token allows a potential client to run the server. It should provide a string which can be passed directly to Wimp_StartTask. This should start with a run command and be followed by the location of the server. This location could be an expanded pathname or more usually a system variable. Note that the RunCommand can contain spaces, and for convenience -R should be the last token in the variable. Examples:
run <Draw$Dir>
/<Draw$Dir>

Session numbers & task handles

To provide context for OLE sessions a session number and task handle should be kept by the client and server for each session opened. Session numbers must be allocated by the client task in a way which makes them unique for the run time of the program. The client should also keep a copy of the server's task handle which it will receive via the OLEOpenSessionAck message. This way it can inform the server whenever it closes down and recognise messages sent by the server.

Note that the combination of client task handle and session number uniquely identifies a session.

A session number is limited to 24 bits (it is unknown why this is), so using pointers to internal data structures as session numbers is not practical. A recommended strategy for generating session numbers by a client is to simply start at 1 when the application starts and increment by one for each new session. Assuming the user starts a new OLE session every 5 seconds for 12 hours a day, seven days a week it will take more than five years for the counter to run out.

See Also

Personal tools